The Refrigeration Cyberattack Advisory

Supermarket refrigeration cyberattacks forced freezers to +50°C. Learn how hackers weaponized defrost cycles, and how UK retailers can secure BMS controllers today.
Hacked into Heaters: How Cyberattacks Turned Supermarket Fridges into 50°C Ovens (And How to Protect Your Plant)
Commercial refrigeration is no longer just copper pipework, mechanical pressure switches, and refrigerant gas. Today, commercial cold chains rely on connected Building Management Systems (BMS), remote IoT supervisory hubs, and IP-enabled temperature controllers.
Recent attacks across Europe demonstrated the vulnerability of unhardened operational technology (OT). Cyberattacks targeted hundreds of supermarkets across France, Belgium, Ireland, and Scandinavia. Attackers remotely hijacked refrigeration supervisory controllers, forcing freezers and multidecks out of refrigeration and locking electric defrost heaters on until interior temperatures climbed above +50°C (122°F).
Stores arrived in the morning to find completely spoiled inventory, puddles of melted produce, and tens of millions of pounds in condemned stock.
With UK intelligence and the National Cyber Security Centre (NCSC) warning operators that critical infrastructure and retail networks remain high-priority targets, commercial facility managers must treat refrigeration security as both an IT priority and a physical engineering priority.
Here is an analysis of how this breach occurred mechanically, along with five critical steps to harden your cold-chain infrastructure.
The Exploit: How Hackers Weaponized the Defrost Cycle
Commercial freezers must defrost regularly to prevent ice from bridging evaporator fins. This process uses either:
Electric Defrost Rods: High-wattage heating elements woven directly through the aluminum coil fins.
Hot-Gas Defrost: Solenoid valves that divert superheated refrigerant discharge gas directly into the evaporator.
Under normal operating conditions, a safety defrost termination thermostat or digital sensor cuts off the heat as soon as the coil reaches a modest setpoint (typically +4°C to +8°C).
The attackers did not breach physical sites; they targeted exposed Human-Machine Interfaces (HMIs) and supervisory systems connected directly to the public internet. By exploiting unpatched firmware or unsegmented network connections, they altered system parameters:
Forced the systems into continuous defrost.
Overrode controller safety limits, elevating the termination threshold to +50°C.
Left high-output electric heaters running inside sealed, heavily insulated boxes.
Within hours, sub-zero holding freezers turned into thermal hotboxes.
5 Steps to Protect Your Commercial Refrigeration & BMS
Securing your cold chain requires bridging the gap between your IT department and your refrigeration service contractor.
1. Close Direct Internet Ports & Require VPNs
Refrigeration supervisory controllers (such as Danfoss AK-SM, Carel Boss, Dixell XWEB, or RDM hubs) should never be exposed directly to public internet IP addresses via basic port forwarding.
All remote engineering access must route through an encrypted Virtual Private Network (VPN) with multi-factor authentication (MFA).
Ensure web management interfaces (HTTP/HTTPS) are restricted to local subnets or whitelisted contractor IPs.
2. Segment Refrigeration on an Isolated VLAN
Refrigeration controllers, sensor gateways, and pack controllers should reside on an isolated Virtual Local Area Network (VLAN) separated from public Wi-Fi, point-of-sale (POS) systems, and corporate office networks. If an office workstation is compromised by phishing, network segmentation prevents lateral movement into mechanical plant controllers.
3. Update Controller Firmware & Decommission Legacy Plant
Many compromised sites operated on end-of-life controllers running legacy firmware with known Common Vulnerabilities and Exposures (CVEs) dating back years.
Audit all on-site supervisory controllers.
Apply vendor firmware patches immediately.
Replace discontinued legacy controllers that no longer receive security updates.
4. Install Hardwired, Independent High-Limit Thermal Cut-Outs
Never rely entirely on a digital software controller for catastrophic temperature cut-offs.
Install independent, hardwired bi-metallic safety cut-out thermostats wired in series with the electric defrost heater contactor coils.
If a software override commands heaters to run continuously, the mechanical thermostat physically breaks the circuit at +15°C, preventing an overheating event regardless of what the digital controller commands.
5. Deploy Out-of-Band Wireless IoT Telemetry
If an attacker compromises your central BMS, they can silence software alarms, preventing your facilities team from being notified.
Implement an independent, battery-powered wireless IoT sensor network (e.g., LoRaWAN) that operates entirely outside of your primary refrigeration controller network.
If internal temperatures drift above safe thresholds, this secondary network sends independent SMS, phone, and cloud alerts directly to store managers and engineering teams.
Audit Your Cold-Chain Integrity with R4NK1N
Refrigeration reliability requires both mechanical precision and secure operational controls. As a SafeContractor-accredited and REFCOM-registered commercial engineering partner, R4NK1N bridges this divide.
We provide comprehensive on-site refrigeration audits across the Midlands and nationwide, evaluating:
Mechanical defrost safety cut-outs and contactor operation.
Supervisory controller firmware, access protocols, and fail-safe settings.
Dual-unit duty/standby failover loops for critical IT, retail, and pharmaceutical storage.
Protect your inventory and secure your critical cooling plant. Call R4NK1N on 0330 043 1804 to book an infrastructure audit.



